Sway bars

[bentley marshall]

after running my sandstrom it need sway bars

nutech are you making them ???? when will they be avalible ???

thanks bentley

[NUTECH RACING]

Bentley,

yes, we have only 2sets of prototype now. will sent one set for Brian test along with his new order.:)

[bentley marshall]

tell him they have to go on my car for testing :good idea::dance::):excited:

[NUTECH RACING]

You tell him please :DLOL:good idea:

[RCKIWI]

tell him they have to go on my car for testing :good idea::dance::):excited:

Bad Idea lol They will be going on my car first!

[NUTECH RACING]

in stock now.

http://www.nutechracing.com/english/ProductShow.asp?ID=857

http://nutechracing.com/english/UploadFiles/057631.jpg

[mynameismud76]

Hi Chris =)

These look great! What size(s) are they please?

[RCKIWI]

Hi Chris =)

These look great! What size(s) are they please?

They are 3.5mm front and rear

[Nutech Ben]

They are 3.5mm front and rear
Yes, it's right!

Diameter:3.5 mm
Ball Joint: ø4/M4

[mynameismud76]

Cool..any plans for different sizes in the future ? =)

[hndaman1]

I have the sway bars kit on my TB-2 what holds them on? just those 2 little screws? when I try to tighten them down they just come right off?do I need to put a washer on there also?

[mradlin]

I have the sway bars kit on my TB-2 what holds them on? just those 2 little screws? when I try to tighten them down they just come right off?do I need to put a washer on there also?

There should be a washer on there also.

[hndaman1]

There should be a washer on there also.

ok, cause in the kit it was just 4 long bolts for the swing arms and 4 short ones for the gear boxes, so what are the little rubber fuel tubing pieces suppose to do? I wish they had the same setup as the baja, :good idea:

[mradlin]

I'm not sure about the fuel tubing Matt. I'm sure someone will chime in to help though.

[Nutech Racing U.S.A]

ok, cause in the kit it was just 4 long bolts for the swing arms and 4 short ones for the gear boxes, so what are the little rubber fuel tubing pieces suppose to do? I wish they had the same setup as the baja, :good idea:

Matt can you get me a picture of where you need the washers? I just got rid of my last sway bar until my new order arrives and I haven't installed one yet they sold out to quick lol.

As for the rubber fuel tubing see image below from Nutech

http://i85.photobucket.com/albums/k55/Sticky_010/DSC04426.jpg

Thank You,
Scott
Zero Gravity RC

[Obeast44]

The short screws that screw into the diff case need a washer or a plastic tab to help hold the bar in place. I will edit this post with a pic of the Baja Swaybars mounted to help demonstrate what I mean. Also did I get the last set? :D :D

[Obeast44]

Wouldnt let me edit after 10 minutes so here is exactly what im talking about. This is the Integy swaybar kit for the Baja, the little orange tabs in the red box screw onto the diff and hold the sway bar in the "slot". Something like this needs to be added because the screws or washers (my kit didnt have them) wont hold it adequately.
http://i294.photobucket.com/albums/mm87/Obeast44_bucket/Swaybar.jpg

[hndaman1]

Wouldnt let me edit after 10 minutes so here is exactly what im talking about. This is the Integy swaybar kit for the Baja, the little orange tabs in the red box screw onto the diff and hold the sway bar in the "slot". Something like this needs to be added because the screws or washers (my kit didnt have them) wont hold it adequately.
http://i294.photobucket.com/albums/mm87/Obeast44_bucket/Swaybar.jpg

thats what is needed those small orange things for sure.. i wil get pics for u scott

[hndaman1]

thats what is needed those small orange things for sure.. i wil get pics for u scott



after yesterdays run the 1 screw stripped out of my gearbox now:mad::mad:

but I found this for the sway bar kits

http://www.largescalerc.com/AluminumSwayBarMountforBaja.aspx

maybe these can be modified to work with the nutech ones..

http://www.largescalerc.com/images/products/display/hb65rw.JPG